Morso NXLEH Automatic Notching Machine (8" wide material max.)
Part No: N0018L
Availability: Out Of Stock
The NXLEH is an automatic guillotine-style notching machine for the production of beaded face-frames, French-mitered cabinet doors as well as muntin and mullion joints. This model will accept moulding up to 8" wide, allowing the operator to process virtually every face-frame, including wide bottom and top rails.
The completely self contained machine is equipped with a heavy-duty motor and hydralic pump and operates with pressurized hydraulic fluid. An industrial-quality PLC unit controls all movements - a clear acrylic guard and two- hand safety controls are used for safe operation.
Notching Operation (stiles)
Upon adjusting the cock-bead stops to set the notching depth, the moulding is placed on the machine table and one end is rested against a flip-stop. Two safety buttons, located at the left and right hand side of the machine table, are pressed simultaneously to start the cutting cycle:
- Hydraulic clamps secure the moulding against the fence rails
- The cutting head advances toward the operator
- Upon touching the moulding edge, sensors trigger two consecutive downward strokes of the cutting head (trim cut and finish cut)
- The cutting head returns to its home position and the clamps release the material
When set to the lower setting, the complete cutting cycle (trim cut and finish cut) is completed in 1.5 seconds and the resulting cuts are smooth and free of tear-out.
Coping Operation (rails)
Upon adjusting the setscrews in the nylon center fitting, the stop is moved toward the cutting head and locked in place. The rail is placed on the table and pushed against the stop. Both safety buttons are activated and the 45-degree corner is cut. The moulding is then flipped end-for-end and the process is repeated.
Cutting Head Details
To increase the range of applications, we offer matched smaller cutting heads with each machine. These heads are fitted at the MORSO factory and can be replaced in only minutes. The side knives fit on both heads, only the nose knives differ in design.
We highly recommend the purchase of the smaller head to produce haunch joints in window grills, cabinet door mullions, etc. The cast-iron head actually costs less than a second pair of side knives!
MORSO NXLEH series electro - hydraulic guillotine for beaded face-frames include:
- safety guard
- scrap chute
- four short-arm flip-stops and two long-arm flip-stops
- left and right hand side cast iron table extensions
- left and right hand side aluminum fence rails
- one set of original MORSO side knives, factory ground and honed
- one ¾" wide nose knife and one 1" wide nose knife, factory ground and honed
- detailed instructions incl. parts diagrams
Mechanical parts are warranted for twelve months. Complete MORSO warranty terms apply.
Freight Cost Information:
All MORSO NXLEH automatic notching machines are shipped in a plywood crate which is attached to a pallet. This requires the use of a common carrier trucking company but greatly reduces the risk of transport damage to the machine. Shipping charges vary greatly due to different shipping weights, transit times and destination ZIP codes.
If you would like to get a freight quote or to place an order for this machine, please contact our office toll-free at (866)248-0100.
|Max. Moulding Width/Thickness||8" (200mm) / 6 1/4" (155mm)|
|Pump Motor||220 volts, single or three phase, 60 Hz - 1.1 KW, 10 Amp|
|Hydraulic System||1,200 PSI (80 bar) - 1.85 gal. (7 liters) per minute|
|Machine Controls||Industrial PLC unit, proximity switches|
|Nose Knife Capacity||1/2" - 1" width (1/4", 5/16", 3/8" nose knives require smaller cutting head)|
|Extension Tables||heavy cast iron, machined surface, 30 3/4" long, one left and one right hand side|
|Fence Rails||silver anodized aluminum, 59 1/2" total length, one left and one right hand side|
|Flip Stops||aluminum, with locking lever, four with short arm, two with long arm|
|Table Height||33" - floor to table surface|
|Width Including Fence Rails||118"|